We offer a full selection of genuine Jeep Wrangler Oil Coolers, engineered specifically to restore factory performance. Australian Dollars (AU$). NOTE: After removing the upper intake, I strongly recommend covering the lower intake holes and using an air gun to blow any debris out from the sides of the lower intake. Oil Filter Adapter/Cooler. Once the contents are out go ahead and reattached the hose and clamp. The oil filter housing can easily be located above the engine and can be accessed by removing the intake manifold. Idontknow: As you can also see visible oil near the filter housing. Jeep 3.6 oil cooler upgrade your browser. You will also need a pair of pliers and a screw driver for the removal of some clamps and hoses. I used a brake pump with reservoir to remove the oil from the valley and then used needle noise pliers to dab small pieces of rag and soak up the rest of the oil. We're sure you will get the right product to keep that Wrangler running for a long time. Remove 10mm nuts on the driver side intake bracket located closer to the fire wall. Remove Air Box Components (8mm socket or Flat Tip Screwdriver, 10mm socket, 3″ and 6″ extensions) Including one (1) clip on the bottom of the Air Box hose assembly. Included for free with this service.
A clean bucket for coolant and rags or towels. Carefully remove the fuel rails from the passenger side fuel injectors and then the driver side fuel injectors. Remove (3) lines on passenger (right) side of upper intake. Genuine Jeep Wrangler Oil Cooler Engine Oil Cooler. Our mobile mechanics offer services 7 days a week. 3.6 Oil Filter / Cooler Housing. After removing the upper intake, its time to unplug all the fuel injectors and remove the fuel line. The In-Store Pickup option will now be defaulted at checkout. Remove (2) 10mm nuts below the Map Sensor. Your Jeep Wrangler will be happy to know that the search for the right Engine Oil Filter Housing products you've been looking for is over! Use the fitment form at the top of the page to select your exact year and engine type for your Jeep Wrangler. Fits Wrangler (2012 - 2013).
Norwegian Krone (NOK). Some of our top Engine Oil Filter Housing product brands are Dorman. Be reviving an old thread. Jeep 3.6 oil cooler upgrade your flash player. Unplug the Map Sensor – In front of the Oil Fill Tube. Without regular oil changes, the cooler may fail at 50, 000 miles and need to be replaced. If your leak is as bad as mine was when discovered, you will see motor oil on the bottom of the transmission pan, crossmember, and transfer case. Remove foam on top of driver side spark plugs.
The dealership is around $240. 1 bolt is hidden under he previously removed bracket on the passenger side. OIL FILTER/COOLER ADAPTOR removal/replacement: First remove both plugs from the rear of the adaptor housing. Next on the passenger side, remove the two 10mm bolts that holds the bracket onto that side of the intake. By adding this item to your cart, the shipping option will not be available for your order. Remove (2) clips on rear of the upper intake on the passenger side. Using the same lubricant lightly lube the fuel rail injector connections. Confirm New Password. Jeep Wrangler Engine Oil Filter Housing | Advance Auto Parts. Pry the two push pins up to detach the pad from the brackets. This replacement Oil Filter Housing Adapter Kit also comes with a new oil filter pre-installed for a complete and worry free installation. You will be able to remove the hose and clamp once you have taken the housing out. We even have reviews of our OEM and aftermarket Engine Oil Filter Housing products to help you buy with confidence.
The oil filter should also be changed to maximize debris removal. INTAKE REMOVALE: First start by removing the two EGR/intake tubes located on the left side (passenger side) of the intake neck. The keyed knobs where the wipers attach were nothing like the OEM's. 3.6L Oil Filter/Cooler Adaptor Housing Replacement. If you want to confirm the leak before you buy parts or disassemble anything, you should be able to get a camera snake into the engine valley through the front or back of the engine. If you do not have an account but would like to check the status of an order, request a change, or report a problem with an order or shipment, please go to our. Using a T30 Torx driver remove (4) bolts holding fuel rails on the engine.
Maneuver the oil filter/cooler housing up and out, once free of the engine unplug the wiring for the oil pressure sensor and Oil Temperature Sending unit on the back of the housing and the pinch clamp for the cooling line. Oil filter/cooler mounting bolts are torqued to 106 in lbs in a pattern starting from driver side rear, the driver side front, passenger side rear, passenger side front and the very front being torqued last. Upper to lower intake bolts – 106 in lbs. Chrysler, Dodge, Jeep, Ram and their associated vehicle models and part numbers are used in this listing only to identify the vehicles this il filter housing adapter kit fits. The hose is help on by a single clamp that can be removed with pliers. Jeep cherokee oil cooler. Icon_crazy: Last edited: This will help keep unwanted debris out of the intake port after pulling the lower intake off.
Remove (1) connector and (1) clip on the bottom of the Throttle Body housing. Order Status & Returns. Remove the (2) Vent lines on from of the upper intake. Once pulled, you can then remove the clam and coolant hose off. Suggest cleaning the gasket surfaces before reassembly and cover the intake ports until reassembly as to not get anything inside the engine. Fits the following vehicles: Replaces part numbers: 68105583AF, 68105583AE, 68105583AA, 68105583AB, 68105583AC, 68105583AD. This one only lasted 4 months. Remove (2) 10mm nuts on driver side rear of upper intake.
Oil adaptor housing part #5184294-AE (2011-2013) and part #68105583-AE (2014-2016{refer to other posts in this thread in regard to the difference}) You can find the part online much cheaper than the dealership (buy at your own risk). Log In or Create Account (Optional). For installation of the new housing follow the provided ALL-DATA pages for proper torque values and patterns. Remove upper intake bolts (3- 8mm capture bolts). From the TOP of the engine compartment you should be able to see some pooling down in the engine valley where the oil cooler adaptor is located. Most recently I purchased a wiper transmission for my Wrangler - a discontinued Mopar part. For more information, go to Cancer and Reproductive Harm. If and or when my oil cooler assembly goes out i'd like to replace it with that Dorman but per that video i'd be SOL. Now remove all five external torx #8 bolts from the housing. Using a E8 external torx driver or 1/4″ 12-point socket remove the 5 torx bolts holding the oil filter/cooler housing to the engine.
You will be able to see the general area (top transmission bell housing and behind the engine). This will place the bucket where you need it next. Log Into My Account. You will not be able to get the rear coolant hose or clamp off the adaptor housing while it is still mounted in the valley. I made it to 63K miles before having this issue.