I recently changed the battery to my car and now the backup camera does not work. Thank you in advance. Train brilliantly with an AMOLED display. If it is not interrupted then the video or RNS module has problems. Now I'm getting a black screen (before I didn't), and the trunk doesn't open and the camera comes out of its housing. You are currently viewing as a guest! Aussie living in PNG and I imported a 2015 RAV4 through a Japanese company. Reverse camera not working after battery change on android. All the wiring for the camera and boot wiring has been replaced with OEM VW Parts, complete harness change on camera harness and boot wiring harness, where to go from here? Disconnect the battery: With the car off, loosen and disconnect the battery terminals, starting with the negative terminal. If the thing with the functioning of the camera that depends on the operation of certain rear bulbs is true then clearly it must be investigated and confirmed that all work. Can you please show us a picture of where S51 Fuse is located on a 2010 Passat CC Thanks. Only the pink wires and the white / red wire in the black connector and the brown wire in the blue connector are replaced, nothing else.
One thing i have noticed is, when it rains, the screen goes white on reverse and after rain it comes back to distorted lines and bad image. Guru1R3DX Did you change the wires on the right or left? If the message "rear camera not available" appears, then one of the two wire (pink/white and red/white) on right side is interrupted and does not reach 12v on the rear camera. Last edited by Joe Marinaccio; 01-06-2019 at 05:40 PM. I have pulled the inside of the trunk and sidewall covering and the harness looks fine visually. The fix might be as easy as pushing a few buttons. Did they figure out the roots cause. S51 fuse, pink white and brown wires. I will check this later tommorow, and one more question from the video module to the media the harness has cutted red, orange/brown and orange/purple which i suppose is CAN HIGH and CAN LOW and can be connected to the quad lock pins 9 and 10 but what about the red wire? 3 - stock ROM, unrooted. Reverse camera not working after battery change on macbook air. Is the display still foggy? There are 4 wires going into the black connector: 1. Have you ever seen the controller falling?
Ensuring that there are no issues with your Internet service that need your attention is also an important step to consider. Control module connector corrosion??? Does the screen have static, or is it completely black? No reversing camera image but a good solution to have the OPS instead. 10 cm away from the sockets.
And get "Camera Not Available" They told me I was nuts till I had video of it. If the badge is opened but there is no video signal then the fault is the two wires white and pink. In short, you can solve your problem very easily and very cheaply by buying a relay or a capacitor regulator... Prices are from $6-$14... depending on where you get it from... Distorted image quality. The picture of customisation of cam. If the answer is yes then check if you have in the wing, where does this wiring to 12 vcc on the brown wire and also 12 vcc on the two white / red and pink wires. The solution is as simple as you think. Camera and flashlight not working after battery replacement. Will have to try a different unit.
What should we deduce from it? I was able to get the dealer to reduce the charges to half of what they were. And after a couple of month, I got the "rear view camera is currently unavailable" message. Do You have + 12v on the brown wire or not? Replaced battery - Nav system - reverse camera not working. Anyone has any ideas? Multisport & Triathlete. Thank you for posting this solution. Many problems with cameras end up being resolved after a reset. Adam0001 I understand that you want to mount an aftermarket camera and you need voltage from the reverse bulb and you do not know what is the wire to take this voltage... well, you need a measuring device, put the contact (without start the engine) and put the lever in reverse.. after you go in the back and look for the wires that lead to the lamps rear lights on which you have + 12v wires.
They and VW America have failed me. The two wires from the camera (pink and red / white) connect to the video module on terminals 47 (pink) and 48 (red / white) on diagram 2 and 3. Also, any frayed cables ought to be replaced as soon as possible. Print the pictures posted by me and show them where to check) If there is no 12v (see my previous descriptions) the wiring and fuse should be checked to supply the camera (fuse S51 under dashboard)... Probability below 1% to be defective the module of the camera/badge... But when they re-attached the module, they discovered that a motor in the camera would short-out the circuit. While you are doing that make sure that the camera wiring is correctly connected to the back of the head unit. Back-up camera not working. Cut one wire at a time on both ends, approx. Damaged cabling in the side/front of the car leading up to the video unit? Outdated software or drivers for the camera may cause glitches. Process, checked fuses, and have trawled through online sites.
Believe it or not, this causes the whole system, including the camera to shut down. I am now chasing around the used parts market to see if a camera control module can be had. Tclabonte Please read the answer and the solution for your problem above. I still needed to lift the latch to open the rear gate and there was no warning on the dash that the gate was open.
The chances of it failing are very small. "I have a car and the engine does not start" can have 1000 causes, without other indications nobody can identify anything. Same thing happens to me. With a measuring device you can check their continuity from under the hood to the trunk. Furthermore, AUDI is recommended a similar fix on some of the aftermarket car/camera installations... Tommy The rear hood has wires on both sides. Do I need to trace the wires all the way to the source?
Datalinks & Connectivity. Brown wire + 12v ok, but only 6. The first time I looked for it, I couldn't believe that it could be there and that it could be located there, but there it is. Do you prefer: you can order a set of cables if you don't want to complicate things but it will probably take time and cost money or the quick and economical option (I described it somewhere above) cut the respective wires near the plugs, at the ends and replace them with other flexible wires after which you put them in the textile tape and fix them in place. They receive 12v via the S51 fuse that is in the dashboard, inside, behind that small compartment under the light switch.
If anyone wants to follow up my story - starts here In short, I replaced my battery with new one from ebay and changed the module that includes the power buttons, SD card reader and ambient light sensor. FUSION® APOLLO™ WB675 HIDEAWAY STEREO. Skip navigation links. Check and tell me the result... Shuvie, what I mean is, when you put the key in the car and push it in to the run position but not so far as to activate the starter (the same position that the key ends up in after it starts) then the camera operates correctly. I repeated the process repeatedly and found that the badge lifts and the camera is visible each time. I've looked through the cubby hole, bottom right of the stressing wheel, I can see a bunch of fuses but none that say s51. You replaced the short harness from the badge to the connector on the boot lid 4. One thing that is refreshing to know in such circumstances is that troubleshooting is not as complex as some may think. Also note, The eight front and rear parking assist sensors are working. I'll find an auto-electrician to help me. It is the voltage that powers the badge and the hood closure.
Performing a reset restores the camera to new factory settings. Hi Guys, I have VW CC 2013, Video signal while in reverse are really bad as per the photo attached. Backup camera foggy. So, my vw cc 2013 never had a camera, i bought original camera with the wires from a guy who scrapped his car and had camera in it. My opinion: It replaces all the wires that lead from the trunk through the hood pipe but starts with the ones referring to the camera: the two 12v power supplies and the coaxial signal cable.