All about turkey calling + News, techniques, routines, advice, etc.. Post Reply. Tips: • Try different latex thicknesses, and in different layers in your calls. I bought a jig from Ricky Bishop for around $60 called the "lil Jiggy" and it came with enough material to make 20 calls. • cutting/customizing. I'm going to try to get a video a week with working on my property, drone footage, hunting, fishing and just outdoor related stuff. Lil jiggy turkey call building jim.fr. On one end of the frame, there is a small tab that sticks out. • Sometimes bending the aluminum frame of the call to modify how it sits in your mouth will make a big difference in the sound you get. Just fine, saves money. You can put the edges close together or far apart. Take the frame and place the front edge of the frame at the crease and push down flat into the adhesive. I would advise you to start conservatively with your cuts to see what kinds of sounds you are creating with each cut you add to the call. Turkey hunting forum for turkey hunting tips.
In other words, some colors of latex in a specific thickness just seem to make better sounding calls for some reason, obably due to minute differences in the latex sheet properties. Here is a video I made showing how to make a call on the "lil jiggy". The distance between the edge of the first reed and the second is entirely up to you. Feather ridge turkey call jig. It is mounted on the block that stays still, not the block that moves. Start with shallow cuts and deepen them as you go, if needed, making sure to try the call between cuts to see how it sounds.
First of all, you can order the materials for building calls dirt cheap. Generally, you will want to put very little stretch in the reed and then tape the end of the reed down flat to your board, being careful to try to get the latex flat with no (or minimal) wrinkling. Sometimes, you will make a real beauty without adding any cuts at all, but generally speaking, some sort of cut design is needed to get the best sound out of a call.
Every one Ive made w mine was huntable, Mike. This is usually best accomplished by starting at the front edge of the frame and gradually folding the tape over the frame from front to back (you'll get the hang of this soon enough). I use a piece of plastic laminate countertop about 6" wide and 2' long for my board, but you can use whatever you wish to use for this. You can build your calls on any surface that you can keep sanitary and that the scotch tape will stick to.
Choose a reed thickness for the first reed of your call. Pushpin Turkey Call Blog. This method of call making allows you, the individual, to customize each call you make to your own preferences. Take one of your frames and bend it at the middle (at the notches) so that you are bending the adhesive-taped side of the "horseshoes" towards each other. • small mallet or hammer. All of the most popular calls can be made by making careful cuts with your scissors in the reeds, and mainly just the top reed. 003 colors, and a couple of. Reed Stretching: The first step is taping the reed materials to your call making surface in the arrangement you desire. The deeper the cuts (to a point), the raspier the sound generally will be. If that happens, the best thing to do is to take a piece of slick paper (I just use the tape backing off of a used tape), cut it in a triangle shape just wide enough to put between the frame and reeds when inserting the frame, and then pull the paper out once the frame and reed material are positioned in place properly. On: March 13, 2021, 01:56:57 PM ». Anything that is unclear, we can discuss and clarify. Without removing the protective paper on the adhesive side of the tape, fold the tape in the middle (adhesive sides toward each other) and crease it with your fingers so that the center cut-out folds over to create the open area where the latex reeds will sit in the tape.
Bottom line is you can get as many thicknesses/colors as you want to experiment with. Most calls have one to three layers of latex of different thicknesses, and are staggered with different spacing along the layered edges of the call. Here is what it looks like up to this point in the game, notice there needs to be a notch taken off of the stationary block to allow the bar stock enough room to slide back and forth to run your gauge. The tape will have a center cut-out that matches the center reed section of the call. Now, take another small piece of tape and place it on the other short end of the latex reed.
I use a pill bottle lid as a template but there are lots of ways you can cut the tape to your liking. A good standard starting distance is about 1/16" or thereabouts but you can obviously experiment with whatever spacing floats your boat. You can experiment with different cuts on each call you make to obtain the sound that you like, or make the call easier for you to use. If you accidently cut through more than the top reed, you will likely deaden the sound of the call. Of course, you can always order a jig or press, but some are pretty expensive,.. again, for a guy just wanting to build calls for himself and maybe some friends, they are unnecessary.
You are now ready for setting the tape on your call. • call making surface.... a flat, smooth, sanitary surface that scotch tape will stick to. You will need scotch tape, a hammer, and a sharp pair of scissors. On thinner latex, you can just grasp the tab-end and pop it off with a quick jerk. News: GUESTS ARE WELCOME TO REGISTER TO THE FORUM!!! Personally, the kids frames are too small for me, the medium frames a little too big, and the small frames just about right. Repeat with another reed, if you desire, or go to the frame setting.