Anyone know how to get a new DIC to talk to the computer so the MPG etc works. If you do not take steering control, your vehicle will steer and brake gradually to a stop in its current lane. If you have already replaced the cluster and it does not work, then you will need a replacement. I finally got into the dash tonight and took it apart and it looks like I do have 2 burnt out bulbs. This means you will need to look at the sender and make sure it is working correctly. Does the interior light come one when you open the door? 1) I downloaded the 2012 version of section IP () and printed pages IP-10, IP-11, and IP-16. My display did this mid-drive yesterday and it was really bothering me. Digital readout gets garbled, or totally blank, or sometimes works normal. Driver information center does not light up mac. Instrument clusters are the hardest GM part to replace. There is also a recall on 2014 Sierra HD about the air bag inflators. During the day, after driving for a while the LED Information Center panel will fade off and can no longer be seen. On these vehicles, when you turn Super Cruise off, these features will revert to the settings you had previously set for them.
RELATED LINKS AND RESOURCES. Last edited by walters_12; 01-30-2019 at 07:20 AM. I removed the dash cover and screws holding the cluster, then removed and reinstalled the ribbon cable (not the harmed connecting the cluster to the vehicle) on the back of the cluster and is now working.
It appears the only reason it worked at all is that it applied some pressure (temporarily) on the Digital Display module. Driver information center does not light up and listen. I'm willing to bet this is the cause of the majority of the problems with this display. Early in a Lane Change On Demand maneuver, you can cancel it by moving the turn signal stalk away from the direction of the lane change. If the cluster is a direct replacement then it will have a wiring plug that plugs into your current one.
Cliffinthank you again; i am going to the city chev dealer has in stock 17. Our DIC was not lighting up and we tried several of the suggestions above. There is no recall on GMC Yukon vehicle. One screw under airbag cap. Any help would be appreciated. Flashing Green Bar and Solid Green Symbol (1st Alert): Super Cruise is active, but the system detects that you need to pay attention to the road. Driver Information Center Not Working Properly - Cluster. I am sure it has something to do with the control module that changes the brightness of the dash lights from day to night. Yeah, sounds like a bad display on the DIC and the digital ones arent cheap. They said it is the cluster and need to replace the entire instrument panel.
If we cover the light sensor on the dash during the day after a few seconds the headlights, and odometer come on. Flashing Red Bar, Solid Red Symbol, Beeps Sound, and Voice Prompt (3rd Alert): You need to take steering control immediately. Driver Information Display/Cluster Electronics Won't Shut Off. On some vehicles†, Super Cruise can steer to perform a single lane change under certain conditions. If one is dark, then the other two will still be visible, but if they are all dark then the whole screen will be black.
I know how annoying it can be to not have that display functioning. Who'd have guessed the repair would cost $0. This is the same issue with the DIC lights on the side buttons will not go on and those are directly connected to the circuit board, not removable. Pop up upper dash section. HI iwas have same problem and i fixed it, first cover the sensor to turn the DIC display back again after. A voice prompt will tell you to take over steering control. Do you guys know if it is just the type of bulbs I used and I need incandescants or if that part of the circuitboard is shorted out? The fuse box in most cases will have to be replaced. Hey the suggestion from Guru worked. Driver information center does not light up how to. Glad to hear this thread is helping others. Fuel sender can be in error - a bad fuel sender will cause the fuel level gauge to not work correctly. You should experiment for the best location for pressure.
GM vehicles are our exclusive work. Looks like I gotta send it back and wait another. Resetting to the factory setting and it will work. So, my question is: where can I find more info with how-to steps and pictures on how to get this job done? Instrument Cluster Problems Common Repairs: It could be as simple as a fuse - If your instrument cluster is showing incorrect readings then you will have to check the fuse for your cluster. Hello, same happened to my 2012 traverse! What are the symptoms of a bad instrument cluster? What to Do if Your 2011 Silverado Instrument Cluster Not Working –. 2) Remove lower panel #7 (remove one screw and then pull out the panel). What is your cluster/display doing?
Anyone have a similar issue? I had the same problem with my DIC in my GT. If it is a replacement for an existing cluster then you will have to install the new wiring harness and plug. When it is safe to do so, press the SUPER CRUISE button on the steering wheel to engage Super Cruise. Its reasonably easy to install. The information display is blank, but it is backlit, and that back lighting is not residual as you can see between the first and second image.