Signal light bulb straight out of the socket. We're going to lift up. No tools are needed, only a new 9005 headlight bulb. Currently driver's side is very dim and passenger side is out again and vehicle cannot be driven at night. Glass part of the new halogen bulb. Pull Off Black Plastic Bracket.
Move to the front of the vehicle and lay down beneath the front bumper. Replace 11 Bolts & 4 Rivets. You have to remove the front bumper to get to the headlight which is a pain if done yourself. Just try to rest it up there for now. Change chevy malibu headlight without removing bumper kit. 11 Bolts & 4 Plastic Fasteners. In the past, I've had both replaced when one blows out because of how you have access the headlights, the car repair shops charges me $180 and up. Replacing the headlight bulb on a 2014–2016 Chevrolet Malibu is an easy task that falls in the DIY category. The owner's manual was no help at all -- its advice was to consult the dealer for bulb replacements.
Had to replace yet other bulb tonight cause high beam went out. I have replaced tons of bulbs and now the light connector is eroding because of excessive heat conductivity within the system. Despite the replacement of the headlight, the new headlight failed to operate as needed. Move to the underbody cover located below the bumper and insert the 7mm screws. Change chevy malibu headlight without removing bumpers. Very expensive if you pay a mechanic. I went to the local auto parts store and bought a replacement bulb for about $12. Organize Bolts & Screws.
The contact then purchased a third headlight and the headlight also failed to operate. Re-attach the black plastic bracket in place over the top edge of the headlight. Also, my lock and unlock buttons do not work, except for on the passenger side, only the unlock side of the button works. It is not difficult to replace the headlight bulb on a 2014–2016 Chevy Malibu but call a knowledgeable friend or professional if in doubt. Pull Out Plastic Fastener. Change chevy malibu headlight without removing bumper to bumper. It's very frustrating and I've waisted over $500 getting it replaced. Please recall this vehicle. After the repair, the contact stated that she then noticed that the passenger-side headlight was failing to illuminate again. Front bumper needs to be removed to get to headlight. Give it a nice loving bonk. I've replaced headlight bulbs on many vehicles and the 08-12 Malibu is by far the most time consuming one. What we need to do is go down 2 inches. So, all that's left at this point is just to go ahead and line up those headlights and take it for a road test.
My car has just over 70, 000 miles on it. Grasp the base of the bulb with your thumb and forefinger. It was repaired a month ago and now the same problem is again at play. I've been seeing many complaints about headlight failure. For those absolutely stupid things that you see people bring, roll, or toss into your place of business and the people that bring them in. No warning lights were illuminated. Press the clip on the electrical plug and pull out the old bulb. Replaced them both the. Now the headlight assembly can finally be pulled away from the front of the vehicle. My complaints to the manufacturer have gone unheard. Four Wheel Well Clips Removed. There'll be a push clip right here, and then on the other side of this, there's another one there. Test New Headlight Bulbs.
This last time it went out within two hours after changing it. I have replaced both sets of wiring harness for bulbs. Driver side only) The whole sprout will pull out. I have paid for repair and bulb replacement already in the past 2 months. On our vehicle, we remember that the measurement was 28 inches for our axis point. Never was the bulbs it was the wiring! You're going to find there's one on the outer portion right here, 10-millimeter, and then one right over here. Black 10mm bolt into the front of the headlight housing and tighten it.
Insert a new H11 low beam bulb straight into the headlight assembly and rotate it 1/4 turn clockwise to lock it into place. Last Monday the check engine light came on when the transmission was slipping m. The the transmission would no longer shift and the solenoid is stuck open while driving home from work. The manufacturer was not made aware of the failure. We're going to go right along the bottom of the bumper cover, and you're going to see all these bolts. Created Mar 29, 2012. Passenger side low-beam head light keeps going out, and have to replace every six months or less. It costs dearly to have a mechanic take apart the front of the vehicle and work on the lights since you must take off the whole front bumper to access the headlights. Remove your push clips that come along your wheel well to the bumper.
Every 6 months if not more. You don't even have to take the bumper off. Chevrolet Malibu owners have reported 412 problems related to headlights (under the exterior lighting category). Will we have to remove the dashboard to change the oil? Automotive maintenance "how-to" guide was specifically written to. Now, you can reach the three bolts that hold in the headlight assembly; remove the headlight assembly and replace the bulb. The 10mm bolts and close the hood of the car to complete the job. Low Beam Light Bulb. 2 Black Bolts, 2 Silver.
If you look right along here on the bumper cover, you're going to see that there's some tabs. I realize it is dangerous to drive with only one lamp, but the frequency of the problem makes it time an cost prohibitive to continually replace the bulb, especially when it goes out soon after it is replaced. YourMechanic can inspect and replace headlight bulbs on your vehicle as needed. My 2012 chevy Malibu passenger side low beam has gone out for the second time in less than a year. Both headlights were replaced every time one went out. Some people may choose to remove the wheel entirely for easier access to the wheel well liner. Tell us your experiences with Monkey-designed products. To remove the eleven 10mm bolts and four black plastic pop rivets that hold.
Rotate the base 1/4 turn counter clockwise to unlock it from the assembly. 1/4 Turn Clockwise To Lock. It is very frustrating, I felt I had to do this after trying to fix it again last week. Replaced 1 high beam and 2 low beams and the passenger side low beam went out on the way home about 15 miles. People have tried several options for repairs and no luck. Carefully slide this out, and then we need to disconnect the assembly itself. Some of these headlight assemblies have one, two, or even more of them, but you should at least have one. Com this is not only a monetary issue, not only a resource issue, but a significant risk to operator and bystander safety.
Move to the front of the car and gently pull the bumper cover away from the headlight assembly. Maybe it's something with the wires. I'm just going to use some push clips and a screw. Headlight bolts aside in a safe place, preferably with a Post-It note to. I decided to register this complaint after finding a website where I went to try to figure out what was going on. Privacy Policy About Paul & Author Contact Info. I also get a engine power reduced error from a bad connected from the app to the bcm, code p1238. The driver side has the windshield wiper fluid fill in the way, which simply pulls out. Come along the side, just make sure everything is lining up the way that it needs to. Low beams will randomly go on and off, stationary or in movement.